The styropan series of cutting machines of polystyrene allows minimizing work times through quick and accurate cuts. Furthermore the boards intented to be used, can be shaped with versatility in any dimensions required alongside any applicable thickness. Easy to handle, they are the ideal tool for the installation of external thermal insulation of walls, pitched roofs and diagonal cuts in the perimeter insulation.

 


General Descritption - Easyquick II polystyrene cutting system

 

Easyquick II is a handy cutting machine offering flexiblility during works. Both expanded polystyrene and extruded polystyrene can be cut with this system which uses a hot wire technology. It consists of an aluminum base on which the polystyrene boards are placed for cutting, a cutting bow which carries the wire having the possibility of torsion angles in the range from 0o - 55o and a transformer. The wire is heated by clicking the start button located on the handle.

The boards to be cut should be clean of glues, adhesives residues or other contaminants.

 

The machine has been made in Germany with the following                                         technical characteristics.  

 Γερμανικής κατασκευής

   

 


Technical Characteristics

        Κόφτης πολυστερίνης λεπτομέρειες



Cutting length:



1300mm 



Cutting depth:



220mm

Transformer:

37V / 160 VA


 κόφτης πολυστερίνης σκαλωσιά

The machine is accompanied by a special butt strap mounted behind the aluminum base and bears special connectors for securing the easyquick on the scaffoldings. Its big advantage is its light weight and its size, which means that there is great flexibility during its transportation on the scaffoldings, saving valuable time for the application workmen. The cuts are now made easily at any point in height while any supplements and special pieces are formed in situ and on the scaffolding.



The ability to turn the handle-arc up to 550 makes the side sections and the creation of beveled edge easy, quick  while, at the same time,  when the heated wire is used, the cuts are clean and extremely accurate. On both sides of the machine we loosen the bolts until we give the desired cutting angle and then we lock the position rotating them again  counterbalancing this time.

 κόφτης πολυστερίνης γωνία στροφής
 κόφτης πολυστερίνης μετασχηματιστής            

          The transformer and its suspension are included.


 

Note: 

It is important to read the following safety use instructions carefully and completely

 

 

- The operator of the unit should be trained and be familiar with the device . During the operation of the unit,  the use of the appropriate personal protective equipment should be made  and all necessary measures required when performing a hot work should be taken.


-The unit can be operated only with the original cables supplied with the purchase. The use of other cables can lead to destruction of the adapter or at increased risk of fire or other damage.

 

-The use of the unit should be done outside or in a properly ventilated area.

 

-The device operates with a low voltage adapter connected to power supply of 220V. It is therefore important to protect the device from moisture. The operation in air or other moisture conditions are not allowed!


- In case repairs need to be made, disconnect the device from the power supply !

 

- Repairs are made only by authorized personnel.

 

- Attention after using disconnect the machine from the power !

 

- The wire is very hot during cutting and should not be contacted in any way . This would result in serious burns . Therefore , it is recommended to use suitable protective gloves . Furthermore , the wire is under high tension . During operation, there is the possibility that the wire be cut and a spark appears . Therefore, the use therefore of protective safety glasses is mandatory !

-Before starting work, all machine screws must be tightened as well as the outputs must be connected correctly.

 

-Before using you should ensure the stable placement and removal of sources of risk from the surroundings.

 

-If the wire is not heated after prolonged continuous use, the adapter can be overheated and must be left to cool.

 

-The button must not be always pressed! (fire hazard)